How to use hydraulic torque wrench (1)

2018-07-13 22:12:11 0

1.JHM/MXTH series square drive torque wrench
Special emphasis: JHJX Hydraulic Torque Wrenches is the power tool for any power tool, indeed, a reliable security prevention are very important, the following is important to note a few suggestions.
●    Read all the technical documents.
●    Try to make the working environment clean and bright. 
If the environment in the workplace air explosion could have any potential, you may not use electric pumps, pneumatic pumps should be used. If metal crash sparks, should take preventive measures.
● Reaction arm 
Hydraulic Torque Wrenches operation requires proper reaction fulcrum, according to the site need to adjust the reaction arm or the appropriate reaction arm position. If still not 
working, please consult the JHJX.  
 
hydraulic torque wrenches                                         hydraulic torque wrench manufacturers
 
 
 
 
● To avoid the tools (Hydraulic Torque Wrenches) misuse 
Pumps operate the remote control just for the wrench to use, to avoid separating the operator and the pump is too far.
 
● Ensure operation of space 
Hydraulic Torque Wrenches is not in use most of the hand, if you must use the hand or in the case of the fixed wrench, should think of other ways to achieve their goals.
● Avoid electric shock 
With electric pump to ensure a good grounding and proper power supply voltage.
● Hydraulic Torque Wrenches should be saved without good 
Temporarily unused Hydraulic Torque Wrenches and wrench accessories should be properly stored to avoid damage.
● Using the appropriate Hydraulic Torque Wrenches 
Not with a small torque wrench or hydraulic accessories to replace the Hydraulic Torque Wrenches work, not unsuitable to work the Hydraulic Torque Wrenches.
● Wear appropriate labor protection products 
When using the manual / motorized hydraulic equipment, you should use gloves, helmets, safety shoes, ear protection, labor insurance and other protective clothing.
●    Safety glasses
●    Mobile Devices 
Do not drag through the hydraulic tubing, rotary joints, hydraulic power cord or external cables, etc. to move the unit. Hydraulic Torque Wrenches comes with handles, can be used to move equipment.
●    High-pressure tubing 
Do not bend, fold tubing, always check the tubing, if damaged, should be replaced.
●    Dust cover and side cover 
All tools have dust cover and side cover, so that internal moving parts and the separation of the external environment, in addition to JHJX professional maintenance staff, users do not want to disassemble or use tools without guards. 
●    Careful to maintain the Hydraulic Torque Wrenches 
To ensure the best performance tool, should always check the tool itself, the power source, tubing, quick connectors, wires, attachments to prevent some common damage occurs. Should be in the proper Hydraulic Torque Wrenches, hydraulic pump unit to repair the maintenance guide. 
More detailed maintenance instructions please refer to maintenance section.
●    Vigilance 
To maintain attention at work, can not be used in an unstable state of power equipment.
●    Preparation before operation 
Ensure that all hydraulic couplings are indeed connected. Check the hydraulic tubing is not entangled, to determine the square head drive shaft and maintain the cap is secure, reliable joint then. Ensure that all connectors, elbows, swivels without distortion or damage.
●    Preparation before use 
Rotate the drive shaft of Hydraulic Torque Wrenches square head is observed with good function. Looking for a fixed surface, choose a good spot, make sure the reaction arm to support reliable, to ensure that the hydraulic tubing is not suppressed. System pressure, if the Hydraulic Torque Wrenches beating or shaking, stop and then re-adjust the reaction arm and the anchor, to make it more solid and safe.
Hydraulic Torque Wrenches - Hydraulic Wrench - Hydraulic Bolt Tensioner 

Note: The operation, reaction arm should be kept clean, and the role of anti-surface between the arms cannot have a foreign body.
● Please stick with quality accessories 
Use high strength sleeve because the sleeve has the exact size of high-quality, and nuts are a good match. Hidden crack has the potential to rupture the sleeve in use, so proper maintenance of the sleeve, the sleeve in operation to keep clean and manipulation. 
Do not use force, but do not use a hammer sleeve, as well as tools to increase the force, if you are not using a Hydraulic Torque Wrenches turn the nut, use a larger device JHJX Hydraulic Torque Wrenches. 
Hydraulic Torque Wrenches - Hydraulic Wrench - Hydraulic Bolt Tensioner 

Note: JHJX designed only to drive the hydraulic pump JHJX Hydraulic Torque Wrenches; improper use may cause damage to the hydraulic pump or Hydraulic Torque Wrenches.
 
 
DRIVE DIRECTION CHANGE
 
To remove the square, disengage the drive retainer assembly by depressing the center round button and gently pulling on the square end of the square drive. The square drive will slide easily out.






Hydraulic Torque Wrenches - Hydraulic Wrench - Hydraulic Bolt Tensioner



FLG 4



 
 
 
 
 
 



To insert the drive in the tool, place the drive in the desired direction, engage drive and bushing splines, then twist drive and bushing until ratchet spline can be engaged. Push drive through ratchet. Depress drive retainer button, engage retainer with drive and release button to lock.
 
 



 Hydraulic Torque Wrenches - Hydraulic Wrench - Hydraulic Bolt TensionerRight is tight.Left is loose.  FLG 5

 
 
 
 
 
 

SETTING THE REACTION ARM
All JHJX’s Torque wrenches are equipped with a universal reaction arm. These reaction arms are employed to absorb and counteract forces created as the unit operates. The reaction arm should extend in the same direction of the square drive; however, slight adjustments may be made to suit your particular application. The function of a reaction:
Device is to hold the tool in position against the forces generated to tighten or loosen bolts or nuts. Hydraulic Torque Wrenches generate tremendous force. The reaction arm can be positioned in numerous places within a 3600 circle. However, for the arm to be correctly positioned, it must be set within a 900 quadrant of that circle. That quadrant is the area located between the protruding square drive and the bottom of the housing away from the swivel inlets. It will always be toward the lower half of the housing and on one side of the housing when tightening and the other side when loosening.
 
SETTING THE SQUARE DRIVE FOR ROTATION
The position of the square drive when looking toward the shroud will determine if the tool is set to tighten or loosen the nut. When the square drive extends to the left when looking at the shroud with the inlets away from you, the tool is set to loosen the nut. When the square drive extends to the right, the tool is set to tighten the nut. To change the direction of rotation for JHM series wrenches simply push the square drive into the housing until the drive projects out the opposite side of the tool.
 
SETTING THE TORQUE
After determining the desired torque, use the torque conversion charts to determine the pressure that is necessary to achieve that torque.
1.      Connect the tool to the power supply and turn the pump on.
2.      Depress the advance remote control button causing the pressure to be shown on the gauge.
3.      Adjust the pressure by first loosing the nut that locks the pressure adjustment handle and then rotate the handle clockwise to increase the pressure and counter clockwise to decrease the pressure. When decreasing pressure, always lower the pressure below the desired point and then bring the pressure gauge back up to the desired pressure.
4.      When the desired pressure is reached, retighten the lock nut and cycle the tool again to confirm that the desired pressure setting has been obtained.




Hydraulic Torque Wrenches - Hydraulic Wrench - Hydraulic Bolt Tensioner

 
 
 
 
 

OPERATING THE WRENCH
1. Place the square Drive in the socket, insert the socket retainer ring and pin, and place the socket to the nut. Make certain the square drive and socket are the correct size for the nut and that the socket fully engages the nut.
2. Position the reaction arm against an adjacent nut, flange or solid system component.
Make certain that there is clearance for the hoses and swivel couplings. Do not allow the tool to react against the hoses, or swivel couplings. When reacting directly off the tool body with reaction arm removed. Do not react off the exposed end plug spigot.
3. After having turned the pump on and presetting the pressure for the correct torque, depress the remote control advance button to advance the piston assembly.
4. When the wrench is started, the reaction surface of the wrench or reaction arm will move against the contact point and the nut will begin to turn. Once the piston reaches the end of its stroke depress the remote control return button to retract the piston.
5. Continue this cycling operation of advance and retract until the nut is no longer turning and the pump gauge reaches the preset pressure. The piston rod will retract when the retract button is pressed and under normal conditions, an audible “click” will be heard as the tool resets itself.
6. Continue to cycle the tool until it “stalls” and the preset psi/torque has been attained.
7. Once the nut stops rotating, cycle the tool one last time to achieve total torque
CAUTION
During the operation, if the tool locks on to the nut, press advance button on remote and build pressure-continue to press down on remote while pushing down on the reaction pawl-release remote while continuing to push down on reaction pawl, then the tool will the released from the nut.
 
 
TROUBLE SHOOTING GUIDE 

TROUBLEPROBABLE CAUSESOLUTION
Piston will not advance 
or retract
Couplers are not securely attached to the tool or pumpCheck the coupler connections and make certain that they are connected.
Coupler is defectiveReplace any defective coupler
Defective remote control unitReplace the button and/or control pendent
Dirt in the direction-consol valve o the pump unitDisassemble the pump and clean the direction-control valve
Piston will not retractHose connections reversedMake certain the advance on the pump is connected to the advance on the tool and retract on the pump is connected to the retract on the tool
Retract hose not connectedConnect the retrace hose securely
Retrace pin and/or spring brokenReplace the broken pin and/or spring
Cylinder will not build up pressurePiston seal and/or end plug seal leakingReplace any defective o-ring
Coupler is defectiveReplace
Square Drive will not turn
 
 
Grease or dirt build up in the teeth of the ratchet and segment pawlDisassemble the Ratchet and clean the grease or dirt out of the teeth
Worn or broken teeth on ratchet and/or Segment PawlReplace any worn or damaged parts
Pump will not build up pressureDefective relief  valveInspect, adjust or replace the relief valve
Electric power source is too 
low
Make certain the amperage, voltage and any extension aord size comply with the pump manual requirements
Defective gaugeReplace the Gauge
Low oil levelCheck and fill the pump reservoir
Clogged filterInspect, clean and/or replace the pump filter
Nut Return with retract stroke
 
Ball Plungers are not engaging the Drive SleevesThread the Ball Plungers to the correct depth in the Housing